Crutchfield Staff Reviews - All Comments

re: Mirage Nanosat speakers: love at first listen

Amanda — Fri, 20 Nov 2009 14:03:17 GMT

Hi Mike,

It’s a little hard for me to give you specific tips on your system’s settings – the fact is that what sounds best for my system in my room may not be what sounds best in yours. But here are some general guidelines:

• Connect your sub to your receiver via the LFE output and set the sub’s filter to “off” so you can use your receiver’s crossover. (One exception: If your receiver only has a crossover frequency of 80Hz, a THX specification, that’d be too low for the Nanosats. In that case, you’d want to keep the filter on and use the sub’s crossover.)

• Ideally, you’ll want to set the crossover high enough that the sub will meet or even overlap with the satellites a bit, so you don’t get any midbass drop out. Mine’s at 120Hz – but again, experiment with different settings to see what sounds best in your room.

• As far as phase goes, that’s 100% dependent on your room. Try listening with it in both positions and see which sounds better to you.

Here are a couple of articles that might also be helpful:

Connecting Your Subwoofer: www.crutchfield.com/.../connect.html

Tuning Up Your Home Theater Subwoofer: www.crutchfield.com/.../0327.html

Also, if you bought your Nanosat system at Crutchfield, feel free to give us a call to get step-by-step help from our tech support folks.

Hope this helps,

Amanda

Social comments and analytics for this post

uberVU - social comments — Wed, 18 Nov 2009 08:25:01 GMT

This post was mentioned on Twitter by CrutchfieldBlog: Ivan wants to know if Mirage Nanosats would be a good match for his Pioneer receiver. Amanda gives her thoughts. http://tinyurl.com/njmtho

re: Mirage Nanosat speakers: love at first listen

MIKE — Mon, 16 Nov 2009 00:06:31 GMT

Hi Amanda,

Since you have the Nanosat Prestige with the S8 could you give me some guidance regarding if you have the crossover mode on active or bypass and what you recommend setting the crossover frequency at on the sub?

Lastly do you need to adjust the phase control at all?

I have the same system and run it through the Pioneer VSX-01 THX and primarily watch movies.

re: Ugrading to the Logitech Harmony 900 remote control

Harley — Wed, 04 Nov 2009 20:16:02 GMT

Yes, it is very easy to update the remote for new equipment. First, you will need to add the device from the supplied category list in the Harmony software, and find the model number for the new component. They have a very extensive list, but you can manually add a device if you do not see it. I have never come across a model that was not in the database to date. Once it is added, you can go through the existing activity setups, and choose the new piece you want to control. You can then choose the new device you want to control. Finally you will need to update the remote via USB. You can also delete an older device if you choose. If you would like to use the new device as RF, you can change that from the remote itself.

re: Ugrading to the Logitech Harmony 900 remote control

srothfuss — Sun, 01 Nov 2009 01:41:14 GMT

How easy is it to update the remote for new equipment? I have always wanted a Harmony One but was afraid to take the 'plunge' because I thought I wouldn't be able to program it / update it properly.

re: Mirage Nanosat speakers: love at first listen

Amanda — Tue, 27 Oct 2009 18:27:24 GMT

Hi Paul,

I’m a little confused by your question, but I’ll do my best to answer it. If I don’t address what you’re asking about, I’d suggest giving our advisors a call at 1-888-955-6000.

You’ll definitely want to place each speaker the way it was designed to be placed. So, for a traditional center channel speaker like the one in this system

www.crutchfield.com/.../Mirage-Nanosat-Prestige-5-Home-Theater-Speaker-System.html

I wouldn’t recommend placing it on its end (I’m guessing it wouldn’t be centered on your TV in this case either?) or on its back ( the sound will get projected backwards, towards the wall, so it’ll sound kind of muffled and muddied). But I think you were asking about this system:

signature.crutchfield.com/.../Mirage-Nanosat-5-1-Compact-Home-Theater-Speaker-System.html

In this case, the center channel is the same size as the satellites – just about the smallest center channel you can find. So if space is an issue, this would be a great choice (though you’d still need to place it upright, facing forward).

Regardless of which center channel option you end up going with, I’d recommend mounting it on the wall above your TV if you just can’t fit it underneath. You can even mount it up near the ceiling, upside-down, if you don’t like the way it looks right above your TV.

Hope this helps,

Amanda

re: Mirage Nanosat speakers: love at first listen

Paul — Mon, 26 Oct 2009 14:58:00 GMT

Amanda,

I'm considering buying the Mirage Nanosat 5.1 system, but I don't have quite enough room for the center speaker to stand upright. I could, however, position the center speaker on its side or back. Would that be an acceptable or appropriate way to position this speaker, or am I expecting too much of this Omnipolar technology?

re: Mirage Nanosat speakers: love at first listen

Amanda — Thu, 15 Oct 2009 14:10:55 GMT

Hi Rob,

The Omni CC will deliver lower frequencies than the Nano CC, and provide more room-filling sound, so normally I’d say go that route. But when it comes to sound quality, proper speaker placement can trump pretty much everything else.

Imagine if you were to place your center channel to the outside of your front right speaker, and a car zoomed across the screen from left to right. You’d hear it as left, far right, then back to the left – it just wouldn’t make auditory sense. Plus, all your on-screen dialogue would seem to come from somewhere off-screen, which would be disorienting. So you’ll want to place your center channel between your front left and right speakers, above or below your TV.

With that in mind, here’s what I’d recommend:

1) Consider wall-mounting your Omni CC above your TV – you can even put it up near the ceiling, as long as you mount it upside-down. You could use paintable speaker wire, or a small paintable cable cover, to help it blend in.

2) Go for the Nano CC right underneath your TV. It won’t play quite as low, but it’ll still sound great.

Hope this helps! Feel free to give our advisors a call with any more questions – 1-888-955-6000.

Amanda

re: Mirage Nanosat speakers: love at first listen

Rob — Sat, 10 Oct 2009 03:30:52 GMT

Hi Amanda,

I was wondering if the NanoCC would effectively replace the OmniCC. My new setup doesnt really allow me to place the OmniCC under the TV (too big) where as the size of the NanoCC would. The only other alternative would be to place the OmniCC on the other side of the front speaker?

System:

Mirage LF150 sub

Mirage Omni 250 -fronts

Mirage Omnistat - rears

Mirage OmniCC - center

What would be the better option?

1) NanoCC - under the TV

2) OmniCC - off center on the other side of the front speaker

With the system as described above.

Thanks

Rob

re: My wish list -- the Onkyo TX-SR606 home theater receiver

KenSpike — Thu, 01 Oct 2009 15:11:01 GMT

Hi Dare --

This receiver doesn't have a CATV input, but you can still enjoy stereo sound through the Onkyo. Connect a set of RCA patch cords from the A/V outputs of the TV to an A/V input on the receiver (aux is a good choice). When you're watching TV, turn the receiver on and set it to that input. Voila!

Ken

re: The Grundig GS350DL radio - tuning in the world

lifran Lienard — Mon, 28 Sep 2009 16:45:45 GMT

Well where it is really made?

China is the bet and the proof was inside. as one of the printed board was bearing the name <Tecsun>

In fact this brand also sells the BCL3000-an exact replica of this set, but with AC220V trans inside & Chinese characters on the front - Some versions with English prints, sold also with a free AC-AC 100Vdown trans-Interesting enough

73s from Japan

re: Mirage Nanosat speakers: love at first listen

Amanda — Sun, 27 Sep 2009 16:06:43 GMT

Hi James,

Though the Mirage speakers do fire upwards, that sound is then dispersed horizontally, so I bet you’d be OK mounting the center channel under the TV. Of course, if you’re planning to wall-mount the front left and right speakers (rather than having them on stands and in reach of your son) you might opt to mount the center channel speaker the same way. I think you’d be fine either way – these speakers do well even when mounted higher up.

I’d be concerned about putting the sub on the shelf though. Creating low frequencies involves moving a lot of air, which means it’ll cause vibrations. It’ll likely rattle the shelf, and anything else on it. So yes, I’d advise placing it directly on the floor.

Hope this helps! If you want more specific placement tips, or have any other questions, give our advisors a call at 1-888-955-6000.

Amanda

re: Mirage Nanosat speakers: love at first listen

James — Fri, 25 Sep 2009 19:22:45 GMT

Hi Amanda,

I have been doing research on speakers for seemingly forever, well the last 6 weeks or so. I came across your review of the Nanosat Prestige and liked what I heard. Specifically I am interested in the Prestige+ Omni s8 combination.

Here's my situation: 50" plasma mounted on swivel/tilted arm so it sits around 8 inches off the wall. My initial intent on the center channel was to mount it directly below the TV (6 inches or so), will I see any odd sound issues with the upward firing speakers essentially being under the tv? Should I look at possibly mounting it above the tv and firing down? I'm already planning on mounting the rears upside down behind us on the wall, can/should I look at doing the same with the fronts as well? My goal is to have everything mounted on a wall where it will be out of reach of my son and have it sound good.

With regards to the sub, should that go on the floor? I ask because my wife wants to put it on a bottom shelf of a shelf system to "hide" it. I'm thinking the carpeted floor might be better.

Any suggestions you have are very much appreciated.

I have the Denon 1910 if that affects your answer.

All the best,

James

re: My wish list -- the Onkyo TX-SR606 home theater receiver

dare — Wed, 23 Sep 2009 12:16:06 GMT

I have an older TV that only has scat; a/v(L + R) and S-video. I would like to know how to connect cable TV to an Onkyo 606 and then to my TV so that I can watch TV and have audio from the Onkyo.

Any help is appreciated.

re: Mirage Nanosat speakers: love at first listen

Shawn — Mon, 21 Sep 2009 17:26:44 GMT

Hi Amanda,

I have a set of OM-r2's(that are listed as surrounds) that i'm currently useing in a 2.1 setup. I'm looking at getting a set of the nanostats and a CC. The room they are going in is medium-small and is irregular shaped. the om-r2's are to heavy to mount on the walls and the floor doesn't allow for good stand placement. My question is. Could i use the om-r2's as front speakers and the Nanostats as rears? Any recomendations would be great.

thanks,

Shawn