Browse by Tags

I do understand where you are coming from and seeing as how this unit is not CEA2006 compliant, it may not put out that wattage. However, I have seen amps before that did not even have a fuse in them. In other words, they have no protections circuitry. Now, it may still fail if connected improperly,...

What are the advantages/disadvatages to wiring an amp using a LOC or high level input? I'm considering getting the Kicker CompVR 07CVR82 and the Kicker ZX400.1 amp and installing it to my factory stereo. The sub is a 2 ohm DVC, so I would wire it in series then? Also is this a good amp for the sub? going...

Engine noise can come in a few different ways. The first is the power wire is pulling the noise from the alternator. We do not have a noise filter that works for amps, but we used to carry one . You will want to search for newer models that have better ratings. The power supply isn't the only potential...

The signal to noise ratio for the Sony XMD-9001GTR amp was pulled from straight from the manual for the unit. While we have not done extensive testing, I would imagine that it is correct. While that specification is important, it alone should not be the deciding factor when choosing an amp. If all the...

Would the gauge of the wire from the battery terminal to the amp have anything to do with the amp goin into protection mode? Would the gauge of the wire from the battery terminal to the am Would the gauge of the wire from the battery terminal to the am Would...

I have a 2005 nissan sentra s it came stock with one sub and a factory amp to power the sub and the four speakers. i recently replace the sub with 2 12" infinity subs and got the 2 channel amp for it. no i replaced all the speakers with the infinity 6022i's. they all have a power rating of about180w...

We carry one amp that outputs 1000 watts RMS at 4 ohms. It is the Alpine PDX-1.1000 mono amp. HTH!!

Hello. Im lookin at putting some subs in my 1995 chevy suburban. I already have an alpine CDA-9883 reciever installed & it sounds great. I'm gonna build my own box & i want to use 3 12" subs, because a suburban is a big truck & i want lots of boom. I want to use 3 kenwood KFC-W3011 subs because...

Can anyone tell me the current draw of these two amps? Kenwood KAC-X1R mono amp and audiobahn A8002T.

Hey Sandman, It sounds like you have a problem at the speakers. If the fuses are not blowing, then the power end of things sounds fine. I would focus on the speakers themsleves and work your way back to the amp. Especially since this started occuring after you installed them. I know you said you don...

how much do you want to sale your kenwood amp KAC-1020.

sony XM-D500X mono amp, 4ga power 8ga ground, fuse on main power. every time i turn the head unit on and it sends a signal to the amp to turn on, the amp turns on for a second then blows its 2 fuses on the amp and shuts off. i have moved the ground cable and everything and only have the power, ground...

We do not carry that amp. Unfortunately, I do not have any feedback to give. Does anyone have any to share?

I agree. Here's some good ones that we carry.... I like the Kenwood KAC-9103D . It has 900 watts at 2 ohms and is good bang for the buck. If your subs can handle 1000 watts between the two of them, then this should be a decent match. The Sony XM-D9001GTR has also received good reviews on our...

I'm trying to design a stereo to install in my '06 Dodge Ram quad cab. I have a few components already... One of my amps, it's a subwoofer amp, I got from my neighbor for helping him with some home improvement projects. Problem is, I can't find ANY information about the specs of the amp - which I NEED...

Hey everybody, I recently purchased a new amp for my 2001 Chevy Silverado 2500 with stock head unit (for now), and I'm a bit stuck at this point. I'm not sure exactly where to hook the power source to the amp up, and I'd rather not go through the firewall to give my amp power, so if anyone would know...

I have 2 audiobahn 12 1 1000 cap 1 distribution block 1 audiofonics ADF 240 800 watt amp 1 audiofonics ADF 241 1000 watt amp How do I hook each amp to each speaker

Is this the correct way to wire my set up? /\ /\? Or is this the correct way? V V? Another question, where dooes the power lead go (the wire which tells my amps that my deck is turned on?) Thanks for the help!

I like Kicker subs quite a bit and the Comp VR series would work well for you. You could go with the CompVR 07CVR124 subwoofer. It is a dual 4-ohm 12" sub that handles 400 watts RMS at 2 ohms. That's a perfect match for your amp and we currently have that for $149.99. It's excellent and you can see these...

Specifically, are the 12" subs the 2-ohm DVC or 4-ohm DVC version? If they are 2-ohm, then you can wire them to a mono amp that can handle a 3 ohm load. If they are 4-ohm, then you can connect them to a mono amp that can handle a 2.7 ohm load. Here is a wiring diagram for 3 2-ohm DVC subs to a mono...

I checked the Alpine SWR-1242D subwoofers and they will handle up to 500 watts RMS power and run at 2 ohms when you parallel the voice coils together. Since you like clean bass and will be getting one subwoofer, but want to be able to hear it, I recommend getting a sealed box and the Kenwood KAC-8103D...

Okay, so Toyota and JBL claim that the 9 speaker upgraded system that I started with in my '07 Rav4 ran a total of 440w from a little amp mounted above the rear wheel well. First, I replaced the OEM subwoofer with a shallow mount in the stock location and put in an auxilliary amp, with a 12 volt converter...

i have 2 Premier 12" Champion Series Subwoofer with 1200 Watts Max. Power 400 watt rms what would be the best amp for about $200 for these subs

i have a battery in my fender on the right side.i was wondering if i could just route the positve amp wire to the fuse box(left side) or does it need to go to battery. I have the speaker wires on the right so ,i have to route the amp wire on the left. it will be easier to jus go to fuse rather than going...

I just picked up an Infinity Kappa Perfect Series 12" VQ Series Sub with a .88 cub ft fiberglass sealed box and I'd like to get an amp that would give me the BEST sound quality/accuracy from the sub...the amp will be hooked up to my pioneer premier HU. Any advice is greatly appreciated!