Browse by Tags

ok now i got a debate on which brand of sub/amp 2 get. My car is a 94 Buick Lesabre Custom. gotta lot of **** trunk space. i'm thinkin bout gettin either 2 12"s or 2 15"s. The stereo i'm gettin is a Pioneer DEH-P5900iB. Now With da subs not sure. Option #1.... Be cheap an get the Alpine bass package...

well it says on the amp " 2 OHM Stable Stereo" so.......... so id just put one sub pos/neg on ch 1 and the other on ch 2 right? and do i hook the stereo up to the inputs or line out????

Well i think i want it so the left sub has left sound and right sub has the right sound. So if i want that i need to do this?????? Right + : Ch1 Right - : Ch2 Left + : Ch3 Left - : Ch4 is that what i need to do? and if i do this will i be able to hook anymore speakers to this amp if i...

Ok so wrapping up this problem from the very beginning................... i only need one disconnect for pos/neg for each speaker because it is all connected to the same metal piece, Sub 1 + : Ch1 Sub1 - : Ch2 Sub2 + : Ch3 Sub2 - : Ch4 and since my amp has 2 sets of inputs and my receiever...

It is not possible to wire two 12" 4 ohm DVC subwoofers to present a 2 ohm load to an amp. You should consider swapping the subwoofers for 2 ohm DVC versions or getting a different amp. If you do change amps, then either find a 1 ohm stable or an amp that outputs the power needed at 4 ohms (2 channel...

carolinasp3: Paul: I did some checking and it appears that the subwoofers you have are dual 4 ohm voice coil. Since you want to connect them to a 2 channel amp, then you will use a combiniation of series and parallel wiring and a diagram showing you how on our web site . I hope this helps! ...

i just recently bought 2-12" Fosgate P1's. i have a 600 watt amp for the speakers in the car and a 650 watt amp for the subs. the first amp is already in but i want to put the new amp and subs in also. how would i hook up the other amp. cuase i was told by a friend that if you dont do it right it could...

I do understand where you are coming from and seeing as how this unit is not CEA2006 compliant, it may not put out that wattage. However, I have seen amps before that did not even have a fuse in them. In other words, they have no protections circuitry. Now, it may still fail if connected improperly,...

What are the advantages/disadvatages to wiring an amp using a LOC or high level input? I'm considering getting the Kicker CompVR 07CVR82 and the Kicker ZX400.1 amp and installing it to my factory stereo. The sub is a 2 ohm DVC, so I would wire it in series then? Also is this a good amp for the sub? going...

OK so I am kind of new to the car audio world and I had some questions on how to upgrade my current system. Two years ago I bought a system from a local car audio store. This included a Memphis Mono Block Amplifier 500.1 at 1 ohm, a 12 inch Memphis M3 Subwoofer, two Memphis M Class Speakers, and an Eclipse...

Engine noise can come in a few different ways. The first is the power wire is pulling the noise from the alternator. We do not have a noise filter that works for amps, but we used to carry one . You will want to search for newer models that have better ratings. The power supply isn't the only potential...

The signal to noise ratio for the Sony XMD-9001GTR amp was pulled from straight from the manual for the unit. While we have not done extensive testing, I would imagine that it is correct. While that specification is important, it alone should not be the deciding factor when choosing an amp. If all the...

Would the gauge of the wire from the battery terminal to the amp have anything to do with the amp goin into protection mode? Would the gauge of the wire from the battery terminal to the am Would the gauge of the wire from the battery terminal to the am Would...

I have a 2005 nissan sentra s it came stock with one sub and a factory amp to power the sub and the four speakers. i recently replace the sub with 2 12" infinity subs and got the 2 channel amp for it. no i replaced all the speakers with the infinity 6022i's. they all have a power rating of about180w...

Hello. Im lookin at putting some subs in my 1995 chevy suburban. I already have an alpine CDA-9883 reciever installed & it sounds great. I'm gonna build my own box & i want to use 3 12" subs, because a suburban is a big truck & i want lots of boom. I want to use 3 kenwood KFC-W3011 subs because...

The Alpine SWR-1022D subwoofers are dual 2 ohm voice coil subwoofers that handle up to 500 watts RMS. That means we will want to get a mono amp that outputs close to 500 watts at 4 ohms and close (if not exactly) double the power at 2 ohms. We have a few amps that fall into that category. Hope that...

We carry one amp that outputs 1000 watts RMS at 4 ohms. It is the Alpine PDX-1.1000 mono amp. HTH!!

Hey all, I have a 2001 Nissan Pathfinder with the "premium" bose package, which is in the least to say crap. It misses most of the lower frequencies even at medium volume. I really don't want to rip out everything but i will if i have to. I just want to add an amp with a kicker sub in the back. The only...

Can anyone tell me the current draw of these two amps? Kenwood KAC-X1R mono amp and audiobahn A8002T.

Hey Sandman, It sounds like you have a problem at the speakers. If the fuses are not blowing, then the power end of things sounds fine. I would focus on the speakers themsleves and work your way back to the amp. Especially since this started occuring after you installed them. I know you said you don...

hi guys i need a good advise, but first i need to give you some feedback i have an: Alpine IVA-W205 Reciver Alpine PDX-4.100 Amp Polk Audio db6500 in the front Polk Audio 690 in the back Now here´s my question : I want to buy the Polk Audio db212-2 Enclosed Subs for my Accord.. What do you...

how much do you want to sale your kenwood amp KAC-1020.

sony XM-D500X mono amp, 4ga power 8ga ground, fuse on main power. every time i turn the head unit on and it sends a signal to the amp to turn on, the amp turns on for a second then blows its 2 fuses on the amp and shuts off. i have moved the ground cable and everything and only have the power, ground...

We do not carry that amp. Unfortunately, I do not have any feedback to give. Does anyone have any to share?

The amp will supply 300 watts total for the two Rockford Fosgate subwoofers. This means that each subwoofer will get 150 watts. As for using the Profile AP600 amp to power your rear speakers, it would not be recommended. You would need a tri-way crossover to do so and most do around a 60/40 split of...