Free Shipping on Most Orders

Browse Site by Tags

Showing related tags and posts across the entire site.

  • wiring config for correct impedance

    i am a total n00b at this whole electricity thing. I mean watts, volts, amps, ohms, impedance. its all chinese to me. I need some guidance. In a nutshell what Im trying to do is add a sub woofer to my home stereo. 1st of all I need to build an enclosure for it. Yes I only have one. (Rock Fosgate 15"...
    Posted to General HT & Audio Discussion by Mastikat on Wed, Nov 18 2009

  • Amp + DVC sub question!

    So I recently bought a used amp, a Pioneer GM-X862. I also just bought a new 12" DVC sub, the Infinity Reference 1252w Now, since this is a dual voice coil sub, I can either get a 2ohm or 8ohm impedance. Here are two examples of what I could do: http://akamaipix.crutchfield.com/ca/learningcenter...
    Posted to Amps by mbowen89 on Fri, Oct 23 2009

  • Tech Terms Demystified: Impedance

    Impedance is one of those tech terms whose meaning is just close enough to its general definition to cause some confusion. In everyday language, an impedance is a hindrance — an obstacle to be overcome. Electrically, impedance is a neutral term — part of the physical properties of electrical...
    Posted to Use & Enjoy Your A/V Gear by Ralph on Mon, Jul 20 2009
    Filed under: Ralph, amplifier, speakers, receiver, tech terms, impedance

  • Re: speaker wire?

    This raises another issue regarding speaker wire, impedance, etc. 1 for the pros here to contemplate. Whenever I am cutting my wires to run from amp to speakers, I measure the length I need to run to the speaker furthest from the amp, then cut both or all 4 wires the same length. My logic here is that...
    Posted to Amps by GLH on Sun, Jul 5 2009

  • Re: watts and ohms

    You need 4 ohm marine grade speakers that can handle 20 watts RMS. I am also in the process of replacing the outside speakers on my camper. Mine are only 2 - 5.25" Jensen speakers, so you know how bad that sucks. I found some Polk marine grade on Crutchfield.com I have my mind set on. I am planning...
    Posted to Speakers by GLH on Tue, Jun 23 2009

  • 2 4-Ohm DVC 15" CVXs

    how would i hook up 2 4-Ohm DVC subs in parallel so i can get it down to a 2-Ohm load for my amp i need the subs to be receiving 1200 watts RMS. im using an Audiobahn a2300HCT 4800W Max, High-Current 2-Channel Car Amplifier RMS Power Rating: 300 watts x 2 chan. @ 4 ohms 600 watts x 2 chan. @ 2 ohms 1200...
    Posted to Amps by Sjost on Sun, May 31 2009

  • Pioneer DEH-P5000UB speaker suggestions

    I just purchased a Pioneer DEG-P5000UB h/u for my 2002 Silverado and I am looking for some advice in selecting speakers. I'm wanting to replace the four factory speakers with speakers that will give me a nice warm, rich sound. Subs are not in the plan until sometime in the future. I'm looking at the...
    Posted to General Car A/V Discussion by cmfloyd on Mon, Dec 1 2008

  • i have an amplifier with an unspecified impedance. can anyone help?

    i have a valor vpa1005 and i'm not sure what the impedance is the description sounds like you can run it at both 4 ohm and 2 ohm. i already have 4 ohm speakers hooked up to this five channel amp, and i wanted to get a sub. preferably what would be better? because the rms at 2 ohm is 600 w and at 4 ohm...
    Posted to Subwoofers by cradlecity on Mon, Nov 10 2008
Page 1 of 17 (340 items) 1 2 3 4 5 Next > ... Last »